All rights reserved. © 2016 Jive Software | Powered by Jive SoftwareHome | Top of page | HelpJive Software Version: 2016.3.2.0, revision: 20161102170127.40d3611.release_2016.3.2 Skip to content Ignore Learn more Please I just tried to make the manual start of openocd, once I am blocked, and it seems to work. Posted by antish on 2016-09-20 07:28 Hi Kevin, Had the same issue. Sign in to comment Contact GitHub API Training Shop Blog About © 2016 GitHub, Inc. http://powerproxy.net/failed-to/failed-to-execute-mi-command-eclipse.html
If I put a "reset halt" as The last step I would be back to the slow clock again. I did not even restart eclipse between the two debug sessions and as I already said the openocd session was always the same. MCU Application Launcher . Even with the generic one it fails.
ilg-ul changed the title from add support for arm-none-eabi-gdb 7.10-2 in Segger J-Link plug-in to Add support for arm-none-eabi-gdb 7.10 Oct 27, 2015 scalpel4k commented Jan 14, 2016 Hi, here I'm I'm using ST-LINK v2.1. GNU ARM Eclipse member ilg-ul commented Oct 7, 2015 perhaps restarting openocd and eclipse before each test will help.
Please don't fill out this field. To tell it in short words: After using a new, empty, fresh workspace and after installing Blinky, CMSIS_CORE_LPC8xx, CMSIS_DSPLIB_CM0 and, finally, lpc800_driver_lib the debugger started working. We encourage you to create a user account on nxp.com to use the new community forums and access NXP microcontroller content. Error In Final Launch Sequence Failed To Execute Mi Command Load Is the Joker based on anything?
How can I solve this issue? Failed To Execute Mi Command Eclipse Same problem GNU ARM Eclipse member ilg-ul commented Sep 20, 2015 then I'm afraid it'll take a while to be fixed, my plug-ins are build on top of GDB Hardware Debugging, What do you mean by "I modified the custom .cfg". http://stackoverflow.com/questions/13068810/eclipse-debug-error-in-final-sequence-failed-to-execute-mi-command If the same error is displayed, please copy the openocd process output (on the Debug perspective, select the openocd process under your debug session, the output should be displayed on the
Not sure how I got into this situation... Failed To Execute Mi Command: -target-select Remote Localhost:3333 Railcrafti commented Sep 20, 2015 It is not possible. Terms Privacy Security Status Help You can't perform that action at this time. Perhaps I should mention: I have another eclipse installed (eclipse-cdt/Juno), but it didn't run during all this.
I could install LPCXpresso in an WinXP-box, but that could not be the desired solution. this website That works. Undefined Maintenance Set Command: Print-stack Off". Mi"help All Rights Reserved. Error In Final Launch Sequence Failed To Execute Mi Command Maintenance Set Python Print-stack Off My gdb debugger is set up correctly /carambola/carambola/build_dir/toolchain-mipsel_r2_gcc-4.6-linaro_uClibc-0.9.33.2/gdb-linaro-7.2-2011.03-0/gdb/gdb ( executing this i can get gdb shell ) any idea what i am doing wrong ?
I also have modified my openocd.cfg file to include the gdb-flash-write-end and gdb-flash-write-start events which call reset init. No idea. So where is my bottleneck then? Salzi commented Oct 7, 2015 Sorry I'm currently unable to test the original gdb hardware debugger lrodorigo commented Oct 15, 2015 Hi, I'm currently experiencing same issue, on Arch Linux with Failed To Execute Mi Command Var-create
none of those "tick" options (or lack of them) allow me to execute a "reset init" in the correct order ... more Active forum topics I can't debug code with LPC11U35 and LPC-Link LPC 1857 SPIFI interfaced Quad SPI Flash (S25FL512) usage for both code execution and data storage. Which current networking protocol would be the optimal choice for very small FTL bandwidth? STLINK V2 ?
Does this work for you as well? Failed To Execute Mi Command: Exec-run time permitting, I'll further investigate. I believe this because it somehow takes time to connect the board for openocd, ans since eclipse starts gdb in the same time, there is a timer elapsing.
And I could not find help. As openocd runs under cygwin, It is hard to run it by just typing "openocd" and as a pipe ... please redo, using exactly the same debug configuration (preferably j-link), the only change being in the environment to execute different gdb versions. Error Message From Debugger Backend Forum content and FAQs have been moved to community.nxp.com.
Of course you need to change the stm32-specifics if you have the LPC part. Instead of this method. One might think, the probe wasn't installed correctly, but I could download Blinky and it blinks as expected. However, when I start up the debugger, I get this error: ------ Error in final launch sequence Failed to execute MI command: target remote | openocd --pipe Error message from debugger
All Rights Reserved. Undefined maintenance set python command: "print-stack off". I'm afraid, a have seen this box in one of my very first attempts, but in never showed up again and I (sorry) forgot it. Binary Not Found.” Snow Leopard and Eclipse C/C++ IDE issue940'Must Override a Superclass Method' Errors after importing a project into Eclipse1562“Debug certificate expired” error in Eclipse Android plugins3Eclipse debug: “Error in
You signed out in another tab or window. This is my first time running stock Eclipse so there are many things that I'm recently coming up to speed with. Sign up for free to join this conversation on Report message to a moderator Re: Eclipse Juno CDT Error in final launch sequence [message #1019738 is a reply to message #1019674] Sat, 16 March 2013 14:24 Marc