powerproxy.net

Home > Error Code > Hot Tub Error Codes

Hot Tub Error Codes

Contents

err 1 (H20) Prime Failed err 3 Stuck Button err 4 No Water Sensor err 5 Overtemperature err 6 Thermal Cut Out Tripped err 7 Stuck Relay err 8 No Temperature If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. Entire system is disabled. Personal tools Namespaces Article Search Main Page Applications AOL Internet Explorer MS Outlook Outlook Express Windows Live DLL Errors Exe Errors Ocx Errors Operating Systems Windows 7 Windows Others Windows have a peek at this web-site

No action is necessary.I CE2 = Freeze protection. Heater is deactivated * F2 : 4 hours daily filtration * F4 : 8 hours daily filtration * F6 : 12 hours daily filtration * FC : continuous filtration EasyPak Error One sensor has detected 110º * Flo : Improper flow or pressure switch malfunction * Cool : Water temp 20 degrees below set point * ICE : Potential freeze condition has These error codes are similar to the ones previous, however we will be looking at these at another angle.

Hot Tub Error Codes

Sensor plugged into jack B is not working Std Spa operating in Standard Mode. The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. Low speed / circ pump will operate continuously until the temp rises above 45° F. * OH : Over heat.

Rare system error. If pump 1 was turned on due to this reason alone, this message will appear for up to two minutes right after very cold water is detected. Refill, if necessary. Marquis Spa Error Codes Touch any button to reset the system.

System will restart when temp. Balboa Hot Tub Error Codes Pressure switch is not working.SN = Non functional high temperature sensor. Please try the request again. http://www.spadepot.com/spa-error-codes.htm Sending a digital picture is very helpful in helping us to troubleshoot or answer any questions.

At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature Great Lakes Hot Tub Error Codes SEoP : Sensor open or disconnected. Protect from FreezingCover Cleaning and AdviceAcrylic Surface Care and MaintenancePurchase a "Made for Michigan" Spa Cover>Spa Cover MeasuringPurchase a Spa Cover Lift AssistantWhirlpool & Air Bath TubsSystem Cleaning-Home remedyAcrylic Surface Care This article contains information that shows you how to fix Easypak Error Codes both (manually) and (automatically) , In addition, this article will help you troubleshoot some common error messages related

Balboa Hot Tub Error Codes

Rare system error. Flow switches are plumbed in line with the plumbing. Hot Tub Error Codes HeatnSweep 12,782 views 3:28 10 Most Common Hot Tub Problems - Duration: 3:12. Vita Spa Error Codes Balboa Control Systems for Spas or Hot Tubs: pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.OHH = Overheat.

Balboa Control Manufacturer Scroll past Common Error Codes for: What common codes actually mean and what you can check prior to scheduling service Common Spa or Hot Tub Error Check This Out One sensor has detected 118º * OHS : Overheat. This corrupted system file will lead to the missing and wrongly linked information and files needed for the proper working of the application. Contact qualified service technician. How To Fix Flo Error Hot Tub

The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. If water temp drops 20ºF below set temp, low speed pump and heater activates to bring temp within 15º of set temp ICE: Freeze condition. 55ºF detected. Source How does it work?

Note: Internal freeze protection only functions when there is proper power running to the spa, and the control system is operational. Hydropool Hot Tub Error Codes Click here Welcome to our newest forum for those that was on the old forum we had to update the site so please re-register Free spa / Hottub information and adivce Heater is deactivated.Sn2 = Nonfunctional temperature sensor.

The low speed pump or circ.

Transcript The interactive transcript could not be loaded. Low speed pump and heater will activate until spa reaches 65ºF * OH : High temperature condition, has reached 110ºF. One sensor has detected 110º. Hot Tub Error Code Oh drops HL: High limit switch tripped EasyPak Error Codes C: Celsius CL: Current Time of Day ECdu: Econo Mode Duration Econ: Econo Mode Turn On F: Fahrenheit Fldu: Filter Cycle Duration

IC, ICE, ICE2 Freeze Condition detected; Warm up procedure begins. Pressure switch not working SN: Non functional high temperature sensor. Could indicate a flow problem HL High Temperature Alarm HL Temp above 118 degrees HL, HFL, HH, OHH High limit sensor reading 45-48C, or above - check flow HLoH Hi Limit http://powerproxy.net/error-code/ssh-error-codes.html This is a normal spa function; no further action is necessary.When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection.

If alternating with temp, may be temporary condition. HotTubsByArcticSpas 25,336 views 5:52 Dimension One Spa Low Flow FL or FLC Error - Duration: 3:40. If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected. SwimUniversity 59,075 views 5:41 How to Diagnose Your Hot Tub Pressure Switch for Flow Problems | Arctic Spas - Duration: 3:41.

Sensor plugged into jack A is not working Snb Spa is shut down. This feature is not available right now. Spa has shut down. HOT TUB SUPPLY SUPERSTORE 1-800-770-0292 Sunday - Saturday7am - 7pm CST Customer Care | About Us | Contact Us | Track Your Order | Shopping Cart | Login HOME ››

Spa unusable. An incomplete installation, an incomplete uninstall, improper deletion of applications or hardware. See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Ecn: Spa operating in Economy Mode.

Connect With Us